Ask Question
EngineeringEngineering
31 December, 04:20

A 600 MW coal-fired power plant has an overall thermal efficiency of 38%. It is burning coal that has a heating value of 12,000 Btu/lb, an ash content of 5%, a sulfur content of 3.0%, and a CO2 emission factor of 220lb/million Btu. Calculate the heat emitted to the environment (Btu/sec), the coal feed rate (tons/day), the degree (%) of sulfur dioxide control needed to meet an emission standard of 0.15 lb SO2/million Btu of heat input, and the CO2 emission rate (metric tons/day).

I know that the heat emitted in Btu/seconds = 927,865 Btu/second and that the feed rate is 5805 tons/day however I am having trouble with the SO2 content and the COs emission rate.

+1
Answers (1)
  1. 31 December, 04:49
    0
    See step by step explanations for answer.

    Explanation:

    600 megawatts =

    568 690.272 btu / second

    thermal eficiency=work done/Heat supllied

    0.38=568690.272/Heat supplied

    Heat supplied=1496553.35btu / s

    heat emmitted to the atmosphere=heat supplied - work done = (1496553.35-568690.272) = 927863.1 btu/s

    feed rate = (1496553.35) / 12000=124.71 lb/s = 10775184.1056 lb/day=5 387.472 ton / day

    sulphur content released = (0.03*124.71) / (1.496553) = 2.5 lb SO2/million Btu of heat input

    so

    the degree (%) of sulfur dioxide control needed to meet an emission standard = (2.5/0.15) * 100=1666.67 %

    the CO2 emission rate=220 * (1.496553) = 329.241 lb/s = 12 903.0802 metric ton / day
Know the Answer?
Not Sure About the Answer?
Find an answer to your question 👍 “A 600 MW coal-fired power plant has an overall thermal efficiency of 38%. It is burning coal that has a heating value of 12,000 Btu/lb, an ...” in 📗 Engineering if the answers seem to be not correct or there’s no answer. Try a smart search to find answers to similar questions.
Search for Other Answers
You Might be Interested in
A community plans to build a facility to convert solar radiation to electrical power. The community requires 2.80 MW of power, and the system to be installed has an efficiency of 30.0% (that is, 30.
Answers (1)
A piece of corroded metal alloy plate was found in a submerged ocean vessel. It was estimated that the original area of the plate was 800 cm2 and that approximately 7.6 kg had corroded away during the submersion.
Answers (1)
Tech a says that the weight of the flywheel smoothest out the engines power pulses. Tech B says that the flexplate and torque converter perform this same function. Who is correct?
Answers (1)
Previously, you wrote a program named Hurricane that classified hurricanes into five categories using the Saffir-Simpson Hurricane Scale.
Answers (1)
The water behind Hoover Dam in Nevada is 221 m higher than the Colorado River below it. At what rate must water pass through the hydraulic turbines of this dam to produce 50 MW of power if the turbines are 100 percent efficient?
Answers (1)
New Questions in Engineering
List and briefly describe two modern's materials needs
Answers (1)
Write the definition of a method named add that receives a reference to a Scanner object associated with a stream of input consisting of integers only. The method reads all the integers remaining to be read from the stream and returns their sum.
Answers (1)
How are fluids distributed and transported in a fluid power system?
Answers (1)
The sliders A and B are connected by a light rigid bar of length l = 20 in. and move with negligible friction in the slots, both of which lie in a horizontal plane. For the position where xA = 16 in., the velocity of A is vA = 3 ft/sec to the right.
Answers (1)
Two parallel Rivers (A and B) are separated by confined and unconfined aquifer estimate the RATE of seepage of river A to River B per unit length of the rivers
Answers (1)
Home » Engineering » A 600 MW coal-fired power plant has an overall thermal efficiency of 38%. It is burning coal that has a heating value of 12,000 Btu/lb, an ash content of 5%, a sulfur content of 3.0%, and a CO2 emission factor of 220lb/million Btu.
Sign Up Forgot Password?