Sign In
Ask Question
Addisyn Lawson
Engineering
The bars of the truss each have a cross-sectional area of 1.25 in2. If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss.
Answer
Answers (2)
Lillian Foster
Engineering
Suppose you want to design a medical centrifuge to subject samples to normal accelerations of 1000 g's. (a) If the distance from the center of the centrifuge to the sample is 300 mm, what speed of rotation in rpm is necessary? (b) If you want the centrifuge to reach its design rpm in 1 min, what constant angular acceleration is necessary?
Answer
Answers (1)
Carissa Mendoza
Engineering
What is Not considered as metric system? a. Length b. Mass c. Time d. Volume e. Temperature
Answer
Answers (1)
Mariela Macias
Engineering
To operate a vehicle in Florida, you must
Answer
Answers (2)
Jessie Hanson
Engineering
What type of models can be communicated in more than one way.
Answer
Answers (1)
Jaida Mathis
Engineering
It is well established that the thermal efficiency of a heat engine increases as the temperature TL at which heat is rejected from the heat engine decreases. In a effort to increase the efficiency of a power plant, somebody suggests refrigerating the cooling water before it enters the condenser, where heat rejection takes place. Would you be in favor of this idea? Why?
Answer
Answers (1)
Teresa Perry
Engineering
What is the Thermodynamic (Absolute) temperature scale?
Answer
Answers (1)
Johnny Pittman
Engineering
You kick a soccer ball with a mass of 2.5 kg at a speed of 10 m/s towards the net. The soccer ball has a kinetic energy of
(Don't forget your units!)
Answer
Answers (1)
Skyler Bauer
Engineering
In an apartment the interior air temperature is 20°C and exterior air temperatures is 5°C. The wall has inner and outer surface temperatures of 16°C and 6°C, respectively. The inner and outer convection heat transfer coefficients are 5 and 20 W/m2. K, respectively. Calculate the heat flux from the interior air to the wall, from the wall to the exterior air, and from the wall to the interior air. Is the wall under steady-state conditions?
Answer
Answers (1)
Evan Simon
Engineering
A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of + / - 2 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 104 cycles with a factor of safety of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Hint: Initially, assume the size endurance limit modification factor is kb=0.85; then check this assumption after the actual size is determined.
Answer
Answers (1)
Jessie Foster
Engineering
Which of these sensors would be least likely used as an input sensor?
Answer
Answers (1)
Sebastian
Engineering
A vertical piston-cylinder device contains water and is being heated on top of a range. During the process, 10 kJ of heat is transferred to the water, and heat losses from the side walls amount to 80 J. The piston rises as a result of evaporation, and 2 J of work is done by the vapor. Determine the change in the energy of the water for this process.
Answer
Answers (1)
Natalya Carrillo
Engineering
When did joe booker start in the computer field
Answer
Answers (1)
Elianna Fisher
Engineering
What is hot tear in casting? How can we avoid it?
Answer
Answers (1)
Adelaide Byrd
Engineering
What should you, the worker, be aware of with regard to evacuation procedures at your workplace
Answer
Answers (1)
More
1
...
14
15
16
17
18
...
Home
»
Engineering
» Page 16
Sign In
Sign Up
Forgot Password?