Engineering » Page 97

Engineering

Give reasons why the control of dimensional tolerances in manufacturing is important.

Answer Answers (1)

Arabella Hampton

Engineering

0.005098 mega liters to liters

Answer Answers (2)

Engineering

Does the amount of heat absorbed as 1 kg of saturated liquid water boils to saturated vapor have to be equal to the amount of heat released when 1 kg saturated water vapor condenses at 100 degrees Celsius? Explain

Answer Answers (1)

Engineering

Ann's Retail, a women's clothing store, hires female attendants to assist clients in the store's dressing rooms. Larry, a male, applies for, and is refused, a job as an attendant. Larry then sues Ann's Retail for employment discrimination under Title VII. Against the suit, the store has

Answer Answers (1)

Engineering

is sampled at a rate of to produce the sampled vector and then quantized. Assume, as usual, the minimum voltage of the dynamic range is represented by all zeros and the maximum value with all ones. The numbers should increase in binary order from bottom to top. Find the bit combination used to store each sample when rounded to the nearest integer between and (clipping may occur). Note: A partially-correct answer will not be recognized. You must answer all three correctly on the same

Answer Answers (1)

Engineering

Consider the smoothie example given in class: Write down the production function of Tutti Frutti Smoothie example given in class. Make sure that all ingredients are expressed in Oz. Identify the returns to scale of this production function. Is it decreasing, increasing, or constant returns to scale?

Answer Answers (1)

Engineering

What do you understand by gravity?

Answer Answers (1)

Engineering

The specific volume of water vapor at 0.3 MPa, 160°C is 0.651 m3/kg. If the water vapor occupies a volume of 1.2 m3, determine the amount present, in kg.

Answer Answers (1)

Engineering

A centrifugal Blower delivers 6m^3 of air per second against a head of 55mm of alcohol of relative density 0.79 when running at 400 RPM. Calculate the power required if the efficiency os 0.7. Estimate the discharge of a blower of similar design of twice the diameter when discharging against a head of 55mm of alcohol. Calculate the operating speed and the expected power. Air Density is 1.17Kg/m^3

Answer Answers (1)

Engineering

One of the arc welding process is most often used today for welding metal thicker than blank gauge

Answer Answers (1)

Engineering

Technician a says the the ac system sould be evacuated so that all old oil is removed technician b says that evacuation is done to remove moisture from the system who is correct

Answer Answers (1)

Harmony Sanford

Engineering

Which of the following is correct oil viscosity for hybrid electric vehicle?

A. SAE 10W-30

B. SAE 5W-20

C. SAE 0W-10

D. SAE 5W-30

Answer Answers (1)

Engineering

Write multiple if statements: If carYear is before 1967, print "Probably has few safety features." (without quotes). If after 1970, print "Probably has head rests.". If after 1991, print "Probably has electronic stability control.". If after 2002, print "Probably has airbags.". End each phrase with period and newline. Ex: carYear = 1995 prints:

Answer Answers (1)

Engineering

Write a program that generates a random number and asks the user to guess what the number is. If the user's guess is higher than the random number, the program should display "Too high, try again." If the user's guess is lower than the random number, the program should display "Too low, try again." The program should use a loop that repeats until the user correctly guesses the random number.

Answer Answers (1)

Engineering

A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P = 50 kN The elongation of the rod is Ii = l. 40 mm. and its diameter becomes d' = 19.9837 mm. Determine the modulus of elasticity and the modulus of rigidity of the material. Assume that the material does not yield.

Answer Answers (1)